How to Measure For Wooden Blinds

Tips

Use a metal tape measure to ensure accurate measurements.

Brackets Sizes Guide

Use the guide below for the sizes of the brackets to make sure there is sufficient room to fit them.

25mm|35mm Slat Sizes: Depth 53mm|Height 65mm

50mm Slat Sizes: Depth 56mm|Height 71mm

64mm Slat Sizes: Depth 56mm|Height 80mm

Headrail Sizes Guide

Use the guide below for the sizes of the head rails to make sure there is sufficient room to fit them.

25mm|35mm Slat Sizes: Depth 57mm|Height 42mm


50mm Slat Sizes: Depth 74mm|Height 42mm


How to Measure Wood Blinds For Standard Windows

Recess Size

Measure the wall-to-wall width at 3 places and the drop from the top recess to the window sill. Note down the smallest of each of the 3 measurements. Do not make any deductions, we will do this during manufacture. Approximately 10mm from the width to ensure a comfortable fit. You can order in inches, cm, or mm.


Exact Size

Measure the wall-to-wall width at 3 places and the drop from the top recess to the window sill. Add on 30cm to the width and drop to allow for sufficient overhang. The blind will be made to these exact sizes from the top of the track to the bottom of the fabric. You can order in inches, cm, or mm.


Part Tiled Recess

Measure the full width at the top and middle of the recess then the width between the tiles. Use the smallest width and order as recess size. For the drop measure from the top of the recess to the window sill.


How to Measure Wood Blinds For Bay Windows

Angled Bay Windows

Step 1: Choose the slat size

When measuring for angled bay windows you need to allow for the head-rail and valance depth and window handles which affect the size of the blind when fitted.

There are 4 different slats sizes which will affect the sizes of the brackets and head-rail, 25mm/35mm/50mm/64mm.

Once you have chosen the slat size you can use the illustration above to determine the allowance which will be referred to as X for the next step.

Head-rail Allowance:

25mm|35mm slat size: X = 57mm
50mm slat size: X = 74mm
64mm slat size: X = 80mm

Step 2

Find the handles allowance. If you have window handles, measure how far out they protrude. e.g. 5.5cm (55mm) in the image opposite. This will be referred to as Y for the next step.

example Y = 55mm

Calculate total allowance.

Add (Y) to the allowance for the head-rail and valance depth (X) that you noted down from the previous page to get Z.

Total allowance will be calculated using the following:

X + Y = Z

Step 3

Take an A4 sheet of paper and cut in half. Place the two pieces of paper next to each other and mark a line at measurement Z.

e.g.
25mm slat size, window handles 55mm
24mm (x) + 55mm (Y) = 79mm (Z)

1) Place the pieces of paper on the window sill touching the frame and slide together until the two lines meet.

2) Then using a pencil make a mark on the window sill at the point where the corner of the fabric meets the frame.

3) Repeat on the other angles around the bay.

Measure the distance between the two pencil marks on each window around the bay as shown on then illustration. This will give you the widths the blinds will need to be.

Drop

Measure from where the top of the bracket is to be fitted to the window sill. Check the drop all around the bay as it will often differ.

Order all blinds as EXACT SIZE

Box Bay Windows

Option 1: The most common method of installation

This method is designed to ensure that the two side blinds butt up against the front blind which is measured to fill the entire width of the front window.

The first thing to do is decide how you want to fit your blinds. Choose from option 1, 2 or 3. Review the summary next to each image for tips on which is best for your window.

Option 2: The most tricky method of installation

For the confident measurer, this gives a more professional fit as the blinds meet in the corner but is dependent on a minimum frame size larger than the head-rail depth.

Measure from the corner to the glass, if the frame is less than the head-rail depth then go for option 1 or

Option 3: Good if you have small side windows

If the side windows are so small that once the bracket allowance is deducted they will be too small to be made.

This method does result in a gap between the blinds and the glass will be visible.

Option 1: The most common method of installation

1) Measure the full width of the front window. Order as RECESS SIZE

2) Measure the full width of each side window separately as they are often different and note the sizes down then deduct X from that size.

e.g. 25mm slat size : 55mm Handle allowance

Side window 870mm wide

Total allowance: Z = X (24mm) + Y (55mm) = 79mm

870mm - 79mm = 791mm wide

3) Order the two side blinds as EXACT SIZE.


Option 2: The most tricky method of installation

On both corners measure from the corner of the bay to the start of the glass, if either measurement is less than the depth of the head-rail then we recommend to not use this option and use option 1 or option 3.

1) Measure the full width of the front window and deduct TWICE the bracket & handle allowance Z.

e.g. 25mm slat size : 55mm Handle allowance

Front window 2000mm

Total allowance: Z * 2 = X (24mm) + X (24mm) + Y (55mm) + Y (55mm) = 158mm

2000mm - 158mm = 1872mm wide

2) Measure the full width of each side window separately as they are often different and note the sizes down then deduct X from that size.

e.g. 25mm slat size : 55mm Handle allowance

Side window 870mm wide

Total allowance: Z = X (24mm) + Y (55mm) = 79mm

870mm - 79mm = 791mm wide

3) Order the all 3 side blinds as EXACT SIZE.


Option 3: Good if you have very small side windows

1) Measure the full width of the front window and deduct TWICE the bracket & handle allowance Z.

e.g. 50mm slat size : 55mm Handle allowance

Front window 2000mm

Total allowance: Z * 2 = X (24mm) + X (24mm) + Y (55mm) + Y (55mm) n= 158mm

2000mm - 158mm = 1872mm wide

2) Measure the full width of each side window separately as they are often different and note the sizes down, no deductions are made.

3) Order ALL THREE blinds as RECESS SIZE.

DROP

1) Measure the full drop of the window from where the brackets are mounted to the window sill.

How to Measure Wood Blinds For Conservatories

Conservatories generally come in two shapes, angled or square so all you need to do is use the same instructions as for bay windows.